What Is FCC Part 15? EMC for Electronics Entering the US
The FCC Part 15 rules electronics sold in the US must follow, the Class A and Class B split, and how it differs from European testing.
The IEC 61000-6 generic standards used for industrial equipment without its own product standard, and the difference between home and industrial settings.
Manufacturers developing a control panel, a special machine, an industrial automation device or a laboratory test system often face the same question in the CE process: which EMC standard applies to my product? While specific product standards exist for many product groups, there is no product-specific standard for a significant share of industrial equipment.
In that case the generic standards in the IEC 61000-6 series come into play. In this article we explain when generic standards are used, the difference between residential and industrial environments, emission and immunity requirements, how large systems are tested, common problems and special cases for machinery and fixed installations.
EMC standards have a hierarchical structure. At the top are product standards prepared for a specific product group: CISPR 32 and CISPR 35 for multimedia products, IEC 60601-1-2 for medical devices, IEC 61326 for measurement and control equipment and so on. If there is a suitable product standard for a product, that standard applies first.
When there is no product-specific standard, the generic standards in the IEC 61000-6 series are used. These standards define requirements not for a particular product group but according to the electromagnetic environment where the product will be used. Control panels, the electrical equipment of special machines, some industrial automation devices and similar products are usually assessed against these standards.
The IEC 61000-6 series contains separate standards for emission and immunity and divides them by environment. IEC 61000-6-1 defines immunity requirements for residential, commercial and light industrial environments; IEC 61000-6-3 defines emission requirements for the same environments. IEC 61000-6-2 covers immunity for industrial environments and IEC 61000-6-4 emissions for industrial environments.
IEC 61000-6-8, a newer member of the series, defines emission requirements for professional equipment in commercial and light industrial environments. This standard offers an intermediate option for equipment not used in residential environments but not working in conditions as harsh as industrial environments either. Which standard applies is determined by the product's real environment of use.
In industrial environments, immunity levels are higher and emission limits more relaxed. This difference makes sense: in factories, large motors, drives, welding machines and power electronics produce strong disturbances, but there are few sensitive radio receivers nearby. In homes the situation is reversed; disturbance sources are weaker, but radio and television receivers are very close to equipment.
If a product can be used both at home and in a factory, it must meet the requirements of both environments together. This usually means applying industrial immunity levels together with residential emission limits. This combination is the most demanding set of requirements and should be considered in design from the start.
Generic standards bring together the basic EMC tests at levels suited to the environment. On the emission side, conducted and radiated emission tests are applied; on the immunity side, ESD, radiated RF field, fast transient bursts, surge, conducted RF on cables, power-frequency magnetic field and voltage dip tests.
Which test applies to which port is determined by the ports the product has. For example, AC mains tests are not applied to a product with only a DC supply; some tests may not apply to signal cables below a certain length. These details should be listed clearly by port in the test plan.
A significant share of industrial equipment is too large to fit in a standard test chamber. For large control panels, production lines or special machines there are several approaches. The first is to test the subassemblies making up the system separately and assess the conformity of the system as a whole based on these results and good engineering practice.
The second approach is to use large test chambers. Large semi-anechoic chambers such as a SAC-5 and SAC-10 allow large products to be tested as a whole. The third approach is measurement in situ, where the system is installed. Some standards allow in-situ emission measurement for large industrial equipment under certain conditions; but the results are valid only for that installation.
The most common EMC problems in industrial equipment are emissions from motor drives and power electronics circuits. Frequency converters produce strong noise, both conducted into the mains and radiated from motor cables. This noise can also affect other devices inside the panel. Shielded motor cables, correct termination and suitable filters are the basic solutions to these problems.
On the immunity side, sensor inputs connected through long cables, communication lines and control signals are the points that most often cause problems. Running power and signal cables in separate trays inside the panel, terminating cable shields peripherally at the panel entry and using the panel's metal structure as a good reference plane prevent many problems from the start. We explain cable shielding in our article on cable shielding and ferrites.
Machinery is assessed under machinery legislation; however, the electromagnetic compatibility requirements of machinery are met under the EMC Directive. A machine manufacturer must therefore also show that the machine's electrical equipment meets EMC requirements. This assessment is usually made with generic standards or EMC standards specific to machinery.
Fixed installations, large systems permanently installed in a particular location, have a special status under the EMC Directive. These installations do not carry the CE mark; instead they must be installed according to good engineering practice, and this practice must be documented. We explain the EMC Directive in detail in our article on the EMC Directive. For our solutions for electronics manufacturers, see our electronics manufacturing page.
It must meet the requirements of both environments together. This usually means applying industrial immunity levels together with residential emission limits.
Some standards allow it for large industrial equipment under certain conditions, but the results are valid only for the installation measured.
The EMC requirements of machinery are met under the EMC Directive. The machine manufacturer must also show the EMC conformity of the electrical equipment.
No. If a suitable product standard exists, it applies first; generic standards are used when there is no product standard.
For the emissions of professional equipment in commercial and light industrial environments that is not used in residential settings.
Subassemblies can be tested separately, a large test chamber can be used or, under certain conditions, in-situ measurement can be made.
Related Solutions
Your free site survey and quote will be ready within 24 hours.
The FCC Part 15 rules electronics sold in the US must follow, the Class A and Class B split, and how it differs from European testing.
Which directive covers products with Wi-Fi, Bluetooth or cellular modules in Europe, and how their EMC testing changes as a result.
The chamber, equipment and validation steps for organizations that want to set up their own EMC lab and gain ISO/IEC 17025 accreditation.