Wi-Fi Test Chambers and RF Shield Boxes

Test your Wi-Fi, Bluetooth and cellular devices in a repeatable environment sealed off from outside signals. From R&D to the production line, and from a benchtop box to an OTA anechoic chamber.

  • Up to 7.125 GHz for Wi-Fi 6E and Wi-Fi 7
  • Conducted and over-the-air (OTA) setups
  • Fast-acting boxes for production lines
  • Wi-Fi 7 ready2.4 / 5 / 6 GHz
  • Shield boxesBenchtop and inline
  • OTA chambersTRP, TIS, efficiency
Get a Quote for Wi-Fi TestingA tailored quote and site survey appointment within 24 hours

or message us on WhatsApp

Why test in isolation?

Reliable Wireless Testing in a Crowded Spectrum

In a typical office or factory, dozens of Wi-Fi networks, Bluetooth devices and cellular signals are on the air at once. Wireless measurements taken there tell you about the environment, not about your device.

Throughput numbers change from run to run, dropped connections can't be traced, and good units fail on the production line. A shielded test environment cuts out outside signals so every measurement runs under the same conditions.

The opening of the 6 GHz band and the 320 MHz channels that arrived with Wi-Fi 7 have raised the bar for test enclosures too. Shield boxes and chambers now need enough isolation up to around 7 GHz, with internal absorbers, filtered interfaces and cable penetrations that suit the new band.

No Outside Signals

Nearby networks stay out of the test.

Repeatable

Every run under the same conditions.

Fast Cycle

Seconds per unit in production.

Broadband

Wi-Fi, BLE, cellular and UWB.

Solutions

Four Ways to Test, From R&D to Production

The right setup depends on what you measure, how big your device is and how many units you test.

Most Popular

RF Shield Box

Conducted and close-range OTA tests

Benchtopmanual or pneumatic lid
  • Filtered USB, Ethernet and power
  • Coaxial and fiber penetrations
  • Internal absorber and test antenna
Get a Quote

OTA Anechoic Chamber

TRP, TIS, antenna efficiency and patterns

Compact · FARsized to device and antenna
  • Multi-axis positioner
  • Compact range option
  • Cellular and Wi-Fi OTA
Get a Quote

Production Test Station

Fast functional testing in volume production

Inlineconveyor or operator-loaded
  • Pneumatic lid
  • Fixture and test software fit
  • Multi-box layouts
Get a Quote

Shielded Test Room

Large devices and multi-device scenarios

Room-scaleshielded, absorbers optional
  • Multi-device network tests
  • Access point and router testing
  • Channel emulator integration
Get a Quote
Bands covered

For Every Wireless Technology You Test

Wi-Fi 2.4 GHz

2.400 – 2.4835 GHz

802.11b/g/n/ax devices and IoT modules.

Wi-Fi 5 GHz

5.15 – 5.85 GHz

802.11a/n/ac/ax, including DFS channels.

Wi-Fi 6E / Wi-Fi 7

5.925 – 7.125 GHz

320 MHz channels and multi-link operation (MLO).

Bluetooth / BLE

2.4 GHz

Wearables, accessories and sensors.

Cellular

700 MHz – 6 GHz

LTE, 5G FR1, NB-IoT and LTE-M.

UWB

Channels 5 and 9

Ranging and digital key applications.

Wi-Fi 6E and Wi-Fi 7

The 6 GHz Band Changed the Test Setup Too

Wi-Fi 6E moved wireless LANs into the 6 GHz band, and Wi-Fi 7 uses it with 320 MHz channels, 4096-QAM and multi-link operation (MLO) across several bands at once. Devices get faster, and testing them gets harder.

A shield box that was only ever verified up to 5 GHz may not deliver the isolation you expect at 6 GHz. Its shielding, internal absorber, filtered interfaces and cable penetrations should be measured up to 7.125 GHz. Multi-link testing also calls for a setup that can work on more than one band at the same time.

  • Isolation to 7.125 GHz

    Boxes and chambers measured for the new band.

  • 320 MHz channels

    Setups that suit wideband test equipment.

  • Multi-link operation

    Simultaneous testing across bands.

  • MIMO and channel emulation

    Multi-antenna performance testing.

  • Filtered interfaces

    No leakage through USB, Ethernet or power.

  • Regulatory pre-testing

    Get ready for RED and FCC testing.

Standards and methods

What You Can Get Ready For

We build the test setup around the regulatory requirements of your target markets and your own performance tests.

  • EN 300 328

    2.4 GHz wideband data transmission equipment (RED).

  • EN 301 893

    5 GHz RLAN equipment (RED).

  • EN 303 687

    6 GHz RLAN equipment (RED).

  • FCC Part 15

    Intentional radiator requirements for the US market.

  • CTIA OTA

    TRP and TIS for cellular and Wi-Fi devices.

  • Rate vs range (RvR)

    Throughput-versus-range curves with programmable attenuators.

Technical specifications

Typical Technical Values

Values depend on the model and how you will use it. We confirm the exact figures in writing in the quote.

IsolationTypically 80 dB or more, by model
Frequency range700 MHz – 7.125 GHz, 18 GHz optional
LidManual, pneumatic or automatic
InterfacesFiltered USB, Ethernet, power, D-sub
RF penetrationsSMA, N-type and fiber
MeasurementConducted and over-the-air (OTA)
IntegrationTest software and fixture fit
HandoverIsolation test report
Process

From Requirements to Handover

  1. 1

    Requirements Review

    We pin down technologies, test types and volumes with you.

  2. 2

    Solution and Quote

    We define the box, chamber or station setup and quote.

  3. 3

    Build and Integration

    We build the enclosure and integrate fixtures and software.

  4. 4

    Isolation Test and Handover

    We measure isolation across frequency and report it.

Frequently asked questions

Frequently Asked Questions About Wi-Fi Test Chambers

If your question isn't answered here, ask our engineer directly.

PhoneWhatsApp

Do I need an RF shield box or an anechoic chamber?

For conducted measurements, functional tests and production lines, an RF shield box is usually enough. Over-the-air measurements such as antenna performance, TRP, TIS and radiation patterns need an anechoic chamber.

Is our existing shield box good enough for Wi-Fi 6E and Wi-Fi 7?

Its isolation and internal absorber should be measured up to 7.125 GHz. Boxes only verified up to 5 GHz can behave differently in the 6 GHz band; we can measure your current box and report on it.

How large a device fits inside a shield box?

Benchtop boxes are designed for phones, modules and small devices. For access points, routers or larger equipment we recommend larger boxes or a shielded test room.

Can it be integrated into a production line?

Yes. We build inline or operator-loaded stations with pneumatic-lid boxes, fixtures and interfaces that work with your test software.

Can several devices be tested at once?

Yes. In a shielded test room, access points and client devices can be tested together in multi-device scenarios.

Do cabled connections leak signal out of the box?

Not with filtered USB, Ethernet and power interfaces and fiber penetrations. Unfiltered cables, on the other hand, seriously degrade a box's isolation.

How is isolation performance documented?

We measure every box and chamber before handover and deliver a report with isolation values across frequency.

Wi-Fi test chambers

Free Advice on Your Wireless Test Setup

Tell us which technologies you test and how big your devices are; your quote will be ready within 24 hours.

Related Solutions

All Solutions

Get a Quote

Step 1 / 2 · Your Project

What kind of room do you need?
Approximate size