EMC Testing

The Radio Equipment Directive (RED) and EMC for Wireless Products

Which directive covers products with Wi-Fi, Bluetooth or cellular modules in Europe, and how their EMC testing changes as a result.

A product containing Wi-Fi, Bluetooth, cellular connectivity or another radio module is assessed in the European and Turkish markets not only under the EMC Directive but under the Radio Equipment Directive (RED). This distinction directly affects which standards the product is tested to, how the declaration of conformity is prepared and what the technical file contains.

In this article we explain which directive applies to wireless products, how EMC is assessed under RED, what radio performance tests cover, whether using a certified module is enough, the recently added cybersecurity requirements and how to plan test infrastructure.

Which Directive Applies?

In the European Union and Turkey, products that intentionally emit or receive radio waves fall under the Radio Equipment Directive (2014/53/EU). The EMC Directive does not apply separately to these products, because RED covers EMC requirements within itself. In Turkey this directive is applied through a harmonised regulation.

Even a product containing only a small Bluetooth module falls under RED. This means, for example, that a smart home device, a wireless headset or an industrial sensor are assessed within the same basic framework. Products without a radio module are assessed under the EMC Directive and, where necessary, the Low Voltage Directive. We explain the EMC Directive in detail in our article on the EMC Directive.

The Essential Requirements of RED

RED defines several essential requirements for radio equipment. The first is protecting the health and safety of users and others; electrical safety and human exposure are assessed under this heading. The second is electromagnetic compatibility. The third is efficient use of the radio spectrum and avoiding harmful interference; radio performance tests are carried out under this heading.

In addition, RED allows additional requirements to be defined for certain product groups. Within this framework, cybersecurity requirements for internet-connected radio equipment have come into force in recent years. These requirements cover topics such as network security, protection of personal data and protection against fraud, and are assessed with the relevant harmonised standards.

  • Health and safety: electrical safety and human exposure
  • Electromagnetic compatibility
  • Efficient use of the radio spectrum
  • Cybersecurity requirements for certain products

What Changes on the EMC Side?

The EMC assessment of products under RED is usually carried out with the ETSI EN 301 489 series of standards. This series consists of a common general part and specific parts for different radio technologies; for example, there are separate parts for short-range devices, Wi-Fi and Bluetooth equipment and cellular equipment. These standards define emission and immunity tests with conditions specific to radio equipment.

One of the most important differences is that the radio link is monitored during immunity tests. Criteria such as the product not losing its radio link during the test, data rate staying above a certain level or error rate not exceeding a certain limit are evaluated. The radio transmitter's own wanted signal is also treated separately in emission measurements. For multimedia products, standards such as CISPR 32 may also apply alongside EN 301 489.

Radio Performance Tests

RED's spectrum use requirement is assessed through radio performance tests. These tests are carried out to different harmonised standards depending on the radio technology the product uses. For example, there are separate standards for Wi-Fi and Bluetooth equipment operating in the 2.4 GHz band, wireless network equipment operating in the 5 GHz and 6 GHz bands, and cellular equipment.

These tests cover transmitter output power, frequency accuracy, in-band and out-of-band unwanted emissions, receiver blocking performance and spectrum sharing mechanisms. Most tests can be done through a connector; but for products without a connector, measurements have to be made over the air. In that case fully anechoic environments such as an antenna measurement chamber are used.

Is Using a Certified Module Enough?

Many manufacturers integrate ready-made radio modules that have already been tested and whose conformity is documented. This approach can avoid repeating a significant part of radio performance testing, because the module manufacturer's test reports can, under certain conditions, be used in assessing the end product. But using a module does not remove the need to assess the end product itself.

When the module is placed inside the end product, the antenna position, housing material, other circuits on the board and the power supply can change the module's performance and the product's total emissions. The end product's EMC tests must therefore be carried out in every case, and it must be assessed whether radio performance is affected. The manufacturer should document in the technical file that the module's integration conditions have been followed.

Test Infrastructure

Testing products under RED requires several different test environments. EMC emission tests are carried out in a semi-anechoic chamber, and immunity tests with a setup that can monitor the radio link. Radio performance tests need spectrum analysers, signal generators and radio test systems that can measure through a connector.

Fully anechoic rooms or RF test boxes are used to measure the radio performance of products without connectors and to carry out over-the-air performance tests. For manufacturers developing wireless products, being able to do pre-tests in-house significantly speeds up product development. You can find our solutions for telecom and wireless products on our telecom and 5G page.

Technical File and Declaration of Conformity

For a product under RED, the manufacturer must prepare a technical file showing that the product meets all essential requirements and issue an EU declaration of conformity. The technical file contains the product description, design and manufacturing information, the standards applied, test reports and the risk assessment. When harmonised standards are applied in full, the product is presumed to conform to the requirements.

Where harmonised standards cannot be applied in full or do not exist, a notified body may need to take part in assessing the product. This can arise especially with new radio technologies and cybersecurity requirements. Current requirements in target markets should be checked at the start of product development. We explain requirements for the US market in our article on FCC Part 15.

Frequently Asked Questions

Is a simple product with Bluetooth also under RED?

Yes. Every product that intentionally emits or receives radio waves falls under RED, however small its radio module.

Do RED and the EMC Directive apply at the same time?

No. For products under RED, EMC requirements are assessed within RED; the EMC Directive does not apply separately.

Can the module manufacturer's test report be used?

Under certain conditions it can be used in assessing radio performance. But the end product's EMC tests and assessment as a whole are still needed.

Which standard is EMC tested to under RED?

The ETSI EN 301 489 series is usually used. The series consists of a common general part and specific parts for different radio technologies.

Which products do the cybersecurity requirements cover?

They cover internet-connected radio equipment and certain product groups. Scope and standards should be assessed according to the product's function.

How are radio tests done on products without a connector?

With over-the-air measurement methods, in fully anechoic rooms or suitable RF test boxes.

Let's Find the Right Solution for Your Project

Your free site survey and quote will be ready within 24 hours.

Get a Quote

Get a Quote

Step 1 / 2 · Your Project

What kind of room do you need?
Approximate size