Anechoic Chamber Modification and Upgrades

We adapt your existing anechoic chamber to new standards, higher frequencies and bigger products without tearing it down. Every change is handed over with re-validation measurements.

  • Absorber renewal and frequency range extension
  • Turntable, antenna mast, door and penetration upgrades
  • We work on chambers from any manufacturer
  • AbsorbersRenewal and upgrade
  • FrequencyUp to 18 / 40 GHz
  • ValidatedDelivered with a report
Get a Quote for a Chamber UpgradeA tailored quote and site survey appointment within 24 hours

or message us on WhatsApp

When to modify?

Look at the Chamber You Have Before Buying a New One

The steel shell of an anechoic chamber lasts for decades. What ages or falls short is usually the absorber lining, the equipment and the frequency range the chamber was originally built for.

Your product range may have changed, the frequencies you need to test may have gone up, or a new standard may be on the horizon. Foam absorbers collect dust, sag and lose performance over the years. In most of these cases, upgrading the chamber you already have is both faster and cheaper than building a new one.

We start by measuring your chamber and documenting where it stands today. Then we put together an upgrade plan showing what each change will deliver against your goals. Once the work is done, we validate the chamber again and hand over the results in a report.

Assessment

The chamber is measured and documented.

Upgrade Plan

The gain from each option is shown.

Execution

A work plan that keeps downtime low.

Re-Validation

Results proven by measurement.

What we modify

Upgrades That Fit Your Chamber to New Requirements

Absorber Renewal

Full chamber or zones

We replace worn foam absorbers and cracked ferrite tiles to bring reflection performance back.

Frequency Range Extension

Up to 18 GHz or 40 GHz

Hybrid absorbers plus the right antennas, cables and preamplifiers take your chamber to higher frequencies.

SAC to FAR Conversion

Removable floor absorbers

Floor absorbers let your semi-anechoic chamber handle above-1 GHz and fully anechoic measurements.

Turntable and Antenna Mast

New or upgraded

We raise load ratings for heavier products, replace ageing drives and connect automation to your test software.

Doors and Penetrations

Larger doors, fiber, filters

Wider doors for bigger products, plus high-current filters and new fiber and coaxial penetrations.

Control and Monitoring

Cameras, lighting, control room

Low-noise lighting, camera systems and a new control or amplifier room.

Higher frequencies

Taking Your Chamber to 18 GHz and Beyond

Many EMC chambers were built to measure up to 1 GHz or 6 GHz. Wireless interfaces, high-speed digital electronics and newer standards now push testing much higher, and above 1 GHz CISPR 16-1-4 requires the test site to be validated with the SVSWR method.

Absorbers decide how high a chamber can go. In chambers lined only with ferrite tiles, adding hybrid absorbers in front of the tiles lifts high-frequency performance, and absorbers placed on the floor in front of the test volume improve SVSWR. Where needed, we also specify antennas, preamplifiers and cable sets for the new range.

  • Hybrid absorbers

    Added in front of ferrite tiles for high frequencies.

  • Floor absorbers

    Improve SVSWR above 1 GHz.

  • Antennas and preamplifiers

    A measurement chain matched to the new range.

  • SVSWR validation

    1–18 GHz to CISPR 16-1-4.

  • Shielding check

    Re-measured after new penetrations.

  • Software integration

    Correction factors updated.

Warning signs

Six Signs It's Time to Upgrade

Anechoic chambers rarely fail overnight; performance slips gradually. Spotting the signs early lets you act before you get a test result you can't accept.

If one or more of the points below sounds familiar, let's measure your chamber and work out together which upgrade will pay back the most. For ageing chambers, our periodic maintenance service helps keep performance where it should be.

  • NSA or SVSWR near the limit

    Validation results are creeping toward tolerance.

  • Damaged absorbers

    Crushed, faded or crumbling absorbers.

  • Bigger products

    The turntable, door or test volume no longer fits.

  • A new standard

    Higher frequencies or a different method required.

  • Outsourced tests

    Some tests still have to go to an outside lab.

  • Ageing equipment

    Drives and controllers with no spare parts left.

Technical specifications

Typical Scope of Service

Scope depends on your chamber's condition and your goals. We confirm it in writing in the quote after measurement and survey.

ScopeAbsorbers, equipment, doors, penetrations, controls
Frequency range30 MHz – 18 GHz, 40 GHz optional
ValidationShielding, NSA, SVSWR, field uniformity
Chamber typesAny make or model
SchedulingPhased around your test calendar
DocumentationBefore and after test report
Process

From Measurement to Re-Validation

  1. 1

    Measurement and Assessment

    We measure your chamber and inspect absorbers and equipment.

  2. 2

    Upgrade Plan and Quote

    We show the gain and cost of each option.

  3. 3

    Execution

    We phase the work to keep downtime low.

  4. 4

    Re-Validation

    We repeat the measurements and report the results.

Frequently asked questions

Frequently Asked Questions About Chamber Upgrades

If your question isn't answered here, ask our engineer directly.

PhoneWhatsApp

Is it better to modify or to buy a new chamber?

If the shell and shielding are sound, modification is usually faster and more economical. If the shell has widespread corrosion or the chamber is far too small for your new needs, a new chamber may be the better call. After measuring, we present both options side by side.

Can you modify a chamber built by another manufacturer?

Yes. We inspect the panel system, absorbers and equipment during the survey and work with solutions that are compatible with your chamber.

How long will the chamber be out of service?

It depends on the scope. We split the work into phases and plan it around your test calendar to keep downtime to a minimum.

Do all the absorbers need replacing to extend the frequency range?

Not always. Adding hybrid absorbers in front of existing ferrite tiles and placing floor absorbers in front of the test volume is often enough.

Is the chamber re-validated after modification?

Yes. Depending on the scope, we repeat shielding, NSA, SVSWR and field uniformity measurements and hand over the results in a report.

Will it affect our accredited lab?

Changes that affect the site validation require re-validation. We report the measurements in a form you can use directly in your accreditation file.

How often should absorbers be renewed?

There's no fixed interval; it depends on usage, environmental conditions and absorber type. Periodic validation measurements and visual inspection are the most reliable way to tell when it's time.

Chamber modification

A Free Assessment of Your Chamber

Tell us about your chamber and what you want it to do; your survey and quote will be ready within 24 hours.

Related Solutions

All Solutions

Get a Quote

Step 1 / 2 · Your Project

What kind of room do you need?
Approximate size